ICP DAS

Industrial Communication

Search for Subjects

SUBJECT

VIEWS

FAQ TYPE

MODEL

LAST UPDATED

DETAIL

PROFI-5017(C) FAQ

Troubleshooting

2020-04-21

NO.	Subject
Q01	How to read analog value(voltage) from PROFI-5017 at SIMATIC STEP7?
Q02	How to read analog value(current) from PROFI-5017C at SIMATIC STEP7?

PROFI-5024 FAQ

Troubleshooting

2020-04-21

NO.	Subject
Q01	How to output analog value(voltage) from PROFI-5024 at SIMATIC STEP7?
Q02	How to output analog value(current) from PROFI-5024 at SIMATIC STEP7?

GW-7553 FAQ

401

Troubleshooting

2020-04-21

NO.	Subject
Q01	How to connect the PROFIBUS master with GW-7553?
Q02	How to setup configuration between GW-7553 and SIMATIC STEP 7?
Q03	How to set GW-7553 as a Modbus RTU master device? (Example for SIMATIC STEP 7)
Q04	How to set GW-7553 as a Modbus RTU slave device? (Example for SIMATIC STEP 7)
Q05	How to set GW-7553 as a Modbus TCP master device? (Example for SIMATIC STEP 7)
Q06	How to set GW-7553 as a Modbus TCP slave device? (Example for SIMATIC STEP 7)
Q07	How to connect GW-7553 with Utility? (Example for SIMATIC STEP 7)
Q08	How to confirm the firmware version of GW-7553?
Q09	How to download the firmware to GW-7553?
Q10	How to show diagnostic message at SIMATIC STEP 7?
Q11	How to setup configuration between GW-7553 and TIA Portal?
Q12	How to set GW-7553 as a Modbus RTU Master device?(Example for TIA Portal)

GW-7557 FAQ

Troubleshooting

2021-11-04

NO.	Subject
Q01	How to set HART Command in GW-7557 example for SIMATIC STEP 7?
Q02	How to set HART Command (burst mode) in GW-7557 example for SIMATIC STEP 7?
Q03	How to confirm the firmware version of GW-7557?

GW-7552 FAQ

339

Troubleshooting

2020-04-21

NO.	Subject
Q01	How to connect the PROFIBUS master with GW-7552?
Q02	How to setup configuration between GW-7552 and SIMATIC STEP 7?
Q03	How to set GW-7552 as a Modbus RTU Master device? (Example for SIMATIC STEP 7) ?
Q04	How to set GW-7552 as a Modbus RTU Slave device? (Example for SIMATIC STEP 7) ?
Q05	How to configure GW-7552 by the Utility?
Q06	How to confirm the firmware version of GW-7552?
Q07	How to download the firmware to GW-7552?
Q08	How to show diagnostic message at SIMATIC STEP 7?
Q09	How to setup configuration between GW-7552 and TIA Portal?
Q10	How to set GW-7552 as a modbus RTU Master device?(Example for TIA Portal)

I-7550 FAQ

180

Troubleshooting

2020-04-21

NO.	Subject
Q1	How to connect the PROFIBUS master with I-7550?
Q2	How to setup configuration between I-7550 and SIMATIC STEP 7?
Q3	How to confirm the firmware version of I-7550?
Q4	How to download the firmware to I-7550?
Q5	How to show diagnostic message at SIMATIC STEP 7?
Q6	How to send and receive data at SIMATIC STEP 7?
Q7	How to Read/Write I-7000 module for SIMATIC STEP 7?

PROFIBUS Series FAQ

532

Troubleshooting

2021-11-04

NO.	Subject
Q1	How to update GSD file for STEP 7 ?

CAN-2088C FAQ

Troubleshooting

2025-12-30

NO.	Subject
Q1	Does CAN-2088C have function to 120-degree angle of the three-phase PWM output?
Q2	Does CAN-2088C have a signal function using the outputs that a count is reached?
Q3	Do counters of CAN-2088C have minimum on/off times set?
Q4	How much delay of CAN-2088C from hardware input trigger to PWM output?
Q5	Can PWM output of CAN-2088C be with load current up to 1A ~ 2A?
Q6	Does CAN-2088C can output PWM to motor and get encoder data with CAN-2088C counter?
Q7	How to set the Duty cycle of CAN-2088C?
Q8	Do I have to send the PDO message module all the time to have output?

CAN-2024C FAQ

Troubleshooting

2020-04-21

NO.	Subject
Q1	How much is the response time of CAN-2024C AO?

CAN-2000C FAQ

Troubleshooting

2025-12-30

NO.	Subject
Q1	When I set PDO Event Timer to let PDO message auto responses per 1 second and it really work. But if I reboot the CANopen slave module and the setting would gone. How can I save this configuration?
Q2	How can I update the firmware on my CAN-2000C module?
Q3	Why can't I communicate with CAN-2000C serial modules by using CANopen master which is not provided by ICPDAS? At the same time, the ERR LED of CAN-2000C modules is blinking continuously.
Q4	Are the plastic materials of CAN-2000 series REACH certified? Are CAN-2000 series UL certified?
Q5	What is the weight of CAN-2000 series? Is there STEP file available?
Q6	Is there any demo program about how to use CAN-2000C series?
Q7	How to modify the mapped objects in the range 0x1600~0x1609 / 0x1A00~0x1A09?

Product FAQ

PC DAQ Board

PAC

Panel Products

IIoT

Machine Automation

Remote I/O Module and Unit

Industrial Communication

Wireless Communication

Energy Management

Signal Conditioning Module

Software

Accessory

Industrial Communication