1. HOME
  2. SUPPORT
  3. Product FAQ

Product FAQ

SUBJECT VIEWS FAQ TYPE MODEL LAST UPDATED DETAIL
DAQ Cards (ISA/PCI) Software Hardware Multiport 648 Update OS/Firmware/Software PEX-CAN200i-D 2023-06-16
NO. Subject

Software

  
FAQ001: The NT/2K/XP driver installation failed with USER account. What's the problem?  
FAQ002: Can I/O card drivers (for Windows) work with non-x86 CPU ?  
FAQ003: The PIO-PISO.exe program identifies PCI cards correctly, but Diag.exe and demo programs failed and show the error message "Card initialize error" or "No xxx card in this system". What's the problem ?  
FAQ004: How to use two or more cards in the same time without calling ActiveBoard() function again and again?  
FAQ005: How to use OCX (ActiveX Control) in Visual C++ .net 2003?  
FAQ006: How to use the ICP DAS I/O card DLL in C# 2003?
FAQ007: How to use the ICP DAS I/O card DLL in VB.NET 2003?
FAQ008: How to use the ICP DAS I/O card DLL in C# 2005?  
FAQ009: How to use the ICP DAS I/O card DLL in VB.NET 2005?  
FAQ011: How to use DAQ Card in Windows XP Embedded?  
FAQ012: How to modify the software of the PCI-P16R16 that compatible with software of the PISO-P16R16U?  
FAQ015: How to use UniDAQ DLL in a MATLAB environment?   
FAQ016: How to use Card ID?  
FAQ017: How to drive a DAQ card with LabWindows/CVI?  
FAQ018: Why does the timer counter read an incorrect value after selecting the mode, or why is there no timer counter activity?  
FAQ019: How to use I/O Card classic driver in LabVIEW?  
FAQ020: How to use UniDAQ driver in LabVIEW?   
FAQ022: How to process data transmission from multiple DI/DO channels?  
FAQ023: How to control a single channel when performing DI/DO data transmission?  
FAQ024: How do I enable the Memory Dump function during a System Crash?  
FAQ025: How do I use a PCI-TMC12A module to measure external frequencies?   
FAQ026: What’s difference between the signal source frequency and the AD sampling rate?   

Hardware

  
FAQ001: How to identify which PCI board is board_0 or board_1 ?  
FAQ002: What is the settling time of PIO-DA16/8/4 ?  
FAQ005 What’s the difference between an ADC conversion rate and a sampling rate ?  
FAQ007 How to clean the golden fingers of the PCI/ISA/PEX card?  
FAQ008: Why do I get uncertain or incorrect digital input data when digital input channels are unconnected?  
FAQ009: How to measure current signals from the A/D channel on board?  
FAQ010: What is the DIO response time of PIO/PEX-DIO series cards?   
FAQ011: How do I upgrade my DAQ Card from the PCI bus to the PCI Express interface?  

Multiport

  
FAQ001: How to make a loop-back test on a RS-485 port of VXC Card?  
FAQ002: Does VXC series cards support customized baud rate?     
FAQ003: Why can't the COM Ports for the Multi-Port Serial Card be set to start from COM1?  
PISO-CAN Series FAQ 34 Troubleshooting PEX-CAN200i-D 2020-04-20
NO. Subject
Q01 How does these two parameter, Acceptance Code and Acceptance Mask, work in PISO-CAN200/400 ?
Q02 Does LabVIEW CAN driver support other versions of LabVIEW?
Q03 If my PISO-CAN program only has the function ActiveBoard but no the function CloseBoard, there is any resource can't release after I close my program ?
Q04 There are two functions in PISO-CAN library, CAN_Config and CAN_ConfigWithoutStruct. Are them the same?
Q05 What’s the Linux OS that the PISO-CAN200/400U supports?
Q06 Where can I find the driver, utility and setup file versions of the PISO-CAN series devices.
Q07 Why the demo code of PISO-CAN runs fine in 32-bits OS, but there will display an error message, "Unable to load DLL pisocan.dll. The specified module could not be found.”, in Windows 7 Professional 64-bit edition & Windows XP 64-bit edition platform?
Q08 Can the PISO-CAN RTX 8.0 driver be used on the environment of RTX2011 version?
Q09 Does the PISO-CAN series CAN card supports CANopen master/slave functions?
Q10 Why the PISO-CAN RTX demo code displayed an error message when execute the rtss file?
TOP
Follow us
  • © 2020 ICP DAS CO., LTD. All Rights Reserved.