ICP DAS

CAN Bus

Search for Subjects

SUBJECT

VIEWS

FAQ TYPE

MODEL

LAST UPDATED

DETAIL

I-7565-G FAQ

Troubleshooting

2020-04-21

NO.	Subject
Q01	Does I-7565 support CAN baud rate 75K bps?
Q02	Does I-7565 support LabView driver?
Q03	Can I use I-7565 to control CANopen motion?
Q04	Does I-7565 series support ISO 11898-3 or ISO 11519 specification?
Q05	Does the I-7565 support Linux platform?

uPAC-5001D-CAN Series FAQ

Troubleshooting

2020-04-20

NO.	Subject
Q01	Why the uPAC-5001D-CAN2 reboots continually, when sending CAN messages with 10Kbps CAN baud rate via using “polling” method?

I-7188XBD-CAN-G / uPAC-7186EXD-CAN-G FAQ

Troubleshooting

2020-07-08

NO.	Subject
Q01	Doesn't I-7188XBD-CAN have two CAN ports ? Why the web information says that there is only one CAN port on the I-7188XBD-CAN?
Q02	May I have my application program in the I-7188XBD-CAN? If yes, how to download my program into I-7188XBD-CAN?
Q03	Are there library and demos of I-7188XBD-CAN ? How to get them?
Q04	Why my I-7186EXD-CAN can't connect with my PC through Ethernet ?
Q05	Why the 5digit display says E.0001 and the autoexec.bat file can not be executed?
Q06	How can I set the CAN bus baud rate to communicate with the NI USB-CAN device(62.5Kbps, BTR0=0x07 and BTR=0x1C))?
Q07	How can I use this device to accomplish Modbus RTU/ASCII slave function?
Q08	Can the by-pass CAN ports of the uPAC-7186EXD-CAN be used as a redundant CAN bus?
Q09	How can I use this device to accomplish Modbus TCP client to CAN function.
Q10	How to use software buffers for transmitting or receiving CAN messages in XC-100 library?
Q11	How to recover CAN Bus Off status via Calling API?

I-2534 / I-5534-M FAQ

Troubleshooting

2021-11-04

NO.	Subject
Q01	What is the maximum FPS of the I-2534?
Q02	How to implement the 6 ports CAN switch with the I-2534?
Q03	How to manage reduce the data flow in 12 ports CAN switch?
Q04	How much delay time does the I-2534 take?
Q05	How to divide one CAN network into two groups with I-2534 module?
Q06	How to configure CAN 1 as input and CAN 2, 3, 4 as output within I-2534 module?
Q07	If I only connect the I-2534’s CAN 1 & 2 and CAN 3 & 4 is open, it will work fine between CAN 1 & 2 ?
Q08	How to build robust and flow controlled CAN network?
Q09	Update Firmware fail?
Q10	What is the MTBF of the I-5534-M?
Q11	Does the I-5534-M could extend CAN bus length?

ECAN-240 FAQ

Troubleshooting

2020-04-21

NO.	Subject
Q01	In Modbus TCP server mode, the user read the wrong CAN data form CAN port 2.
Q02	When the user set specific CAN ID with CAN 2.0B, the value of CAN ID is incorrect in setting.
Q03	When the user read CAN message with different data length via Modbus TCP command, the Modbus TCP response has invalid CAN data in Modbus format.
Q04	After the user sets the Modbus TCP Client write Table, some CAN-ID values are incorrect.
Q05	How to find or restore the Module's IP when the user forgets it ?

I-2532 / I-2533 / I-2533CS FAQ

Troubleshooting

2021-11-04

NO.	Subject
Q01	What is the difference between I-2532s and I-2533s?
Q02	How to calculate the working distance and the device numbers on the same CAN network while using I-2532s?
Q03	May I mix I-2532s and I-2533s in the same CAN network?
Q04	If some bus error happens on one side of I-2532s, is there any affection to my system?
Q05	If some error happens on one side of I-2533s, is there any affection to my system?
Q06	The Rx and Tx LED are flashing on one side of the I-2532. And the Rx and Tx LED are off on the other side of the I-2532. What happen would make this condition?
Q07	What is the relationship of some error conditions and the Rx and Tx LED of the I-2532?
Q08	Why the I-2532 modules stop to convert the CAN single to fiber single after a long time test?
Q09	I can’t connect with I-2533 via utility v1.01 and it shows error message ”1.03 is not a valid floating point value” .
Q10	Does the I-2533CS series support different CAN bus protocol over its network?