HART
    I-7570
 
 
 
 
 
    HART
 
     

 
 
       
 


I-7570
~ NEW ~

Serial to HART Converter

 
     
 

The I-7570 is a Serial to HART converter designed as the master device of HART protocol. It allows users to access the HART slave by using RS-232 / RS-422 / RS-485. These HART slave devices may be a transmitter, actuator, current output device and so forth. In addition, by using the I-7570 utility tool, users can configure module and test HART communication easily and quickly.

 
 
 
   
 
  • Current Measuring
  • Petrochemical Industry Application
  • Environment Monitoring
  • Tunnel Monitoring
  • Monitor system
  • Building Monitoring

   
 
 
     
 
  • Support HART Short / Long frame
  • Support HART Burst mode
  • Support point-to-point or multi-drop HART mode
  • Support connecting up to 15 HART slave devices
  • Allow two HART masters
  • Provide utility tool for module configuration and HART communication
  • Provide PWR / TxD / RxD indication LED
  • Isolated COM 1: RS-232 / RS-422 / RS-485
  • 4KV ESD Protection
  • Built-in Watchdog
  • Selectable 250[ load resistor
  • Support HART OPC Server provided by HART COMMUNICATION FOUDATION
    ( HART OPC Server : http://www.hartcomm.org/hcf/documents/documents_opc.html => for 30 day trial of the full licensed version )
  • Support FDT (Field Device Tool) technique and the below FDT software have been tested OK

(1) PACTware (PACTware)
(Free download: http://www.pactware.com/en/products/pactware.html)

(2) FieldCare (Endress+Hauser)
(Download: http://portal.endress.com/wa010/FieldCareDownloadGui/)

(3) PDM (Seimens)
(Download: http://support.automation.siemens.com/cn/llisapi.dll?func=cslib.csinfo&objid=35125986&lang=en&siteid=cseus&aktprim=0&objaction=csopen&extranet=standard&viewreg=CN)

 
     
 
 
 
     
 
  • Search all HART devices automatically
  • Provide HART Universal & Common-Practice command (v6.0) for HART device configuration
  • Provide module configuration and HART communication easily and quickly
  • Provide data logging for HART communication

@

 
     
 
 
 
     
 
UART Interface
COM 1
RS-232(Tx / Rx / GND) / RS-422 / RS-485
COM 1 Connector
9-pin screwed terminal block
Baud Rate (bps)
1200 bps (For FW_v1.1)
1200 ~ 115200bps (For FW_v1.1 / HW_v1.2)
Data Format
O(odd parity), 8(data bit), 1(stop bit) (For FW_v1.1)
N/O/E(parity), 8(data bit), 1/2(stop bit) (For FW_v1.1 / HW_v1.2)
HART Interface
HART Interface
2-pin screwed terminal block
HART Channel
1
LED
Round LED
PWR / TxD / RxD
Power
Power supply
Unregulated +10 ~ +30 VDC
Protection
Power reverse polarity protection, Over-voltage brown-out protection
Power Consumption
1 W
Mechanism
Installation
DIN-Rail or Wall Mounting
Dimensions
121 mm x 72 mm x 35 mm (H x W x D)
Environment
Operating Temp.
-25 J ~ +75 J (-13 to 167 K)
Storage Temp.
-30 J ~ +85 J (-22 to 185 K)
Humidity
5% ~ 95%, non-condensing
 
     
 
 
 
     
 
I-7570 CR
Serial To HART Converter (Gray Cover) (RoHS)
 
     
   
Copyright© ICP DAS Co., Ltd. All Rights Reserved