| |
|
|
| |
|
|
| |
PIO-D48
PCI BUS 48-channel OPTO-22 Compatible DIO Board |
|
|
|
|
|
|
|
| |
|
|
| |
|
|
| |
| The PIO-D48 provides 48 TTL digital I/O lines. The PIO-D48 consists of six 8-bit bi-direction ports. The 8-bit port are named port A (PA), port B (PB),port C (PC) and the port C can be split into 2 nibble-wide(4-bit) ports. All port is configured as inputs upon power-up or reset. The PIO-D48 has one D-Sub connector and one 50-pin flat cable connectors, Each header can connect to a 50-pin flat cable. The flat cable can be connected to ADP-37/PCI or ADP-50/PCI adapter. The adapter can be fixed on the chassis. Refer to the above figure. It can be installed in a 5 V PCI bus and can support truly "Plug & Play". |
|
|
| |
back |
|
|
|
|
| |
|
|
| |
|
|
| |
- PCI bus
- Up to48 channels of digital I/O
- All I/O lines buffered on the board
- Eight-bit groups independently selectable for I/O on 24-bit port
- Input / Output programmable I/O ports under software control
- SMD, short card
- Connects directly to DB-24PR, DB-24PD, DB-24RD, DB-24PRD, DB-16P8R, DB-24POR, DB-24SSR, DB-24C or any OPTO-22 Compatible daughter boards
- One 32-bit programmable internal timer
- One DB37 connector, two 20-pin headers(only for PIO-D56)
- One 16-bit event counter
- Interrupt source: 4-channel
- Pull-up or pull-down resistors on I/O lines
- Emulate two industrial-standard 8255 mode 0
- Buffer output for higher driving capability
- One D-Sub connector, one 50-pin flat cable connector
- Automatically detected by Windows 95/98/NT
- No base address or IRQ switches to set
- DIO response time is about 0.77 us (1.3 MHz max.)
|
|
|
| |
back |
|
|
|
|
| |
|
|
| |
|
|
| |
- Toolkit for DOS
- Toolkit for Windows 95/98
- Toolkit for Windows NT
- Toolkit for Windows 2000/XP
- LabVIEW toolkit for Windows
|
- Toolkit for OCX 95/98
- Toolkit for OCX NT
- Toolkit for OCX 2000/XP
- Driver for LINUX
- Driver for DasyLab
|
|
|
| |
back |
|
|
|
|
| |
|
|
| |
|
|
| |
| All inputs are TTL compatible |
| Logic high voltage: 2.4V ( Min. ) |
| Logic low voltage: 0.8V ( Max. ) |
| All outputs are TTL compatible |
| Sink current: 64 mA ( Max. ) |
| Source current: 32 mA ( Max. ) |
| Power |
|
|
| Environmental |
Operating temperature |
0~60¢XC |
Storage temperature |
-20¢XC~70¢XC |
Humidity |
0 to 90% non-condensing |
| Dimensions |
Dimensions |
156 mm x 105 mm |
|
|
|
|
|
| |
back |
|
|
|
|
| |
|
|
| |
|
|
| |
| PIO-D48 |
PCI bus 48-channel DIO board |
| PIO-D48 CR |
PCI bus 48-channel DIO board (RoHS) |
|
|
|
|
| |
back |
|
|
|
|
| |
|
|
| |
|
|
| |
| DB-24P |
24-channel isolated D/I board |
| DB-24R |
24-channel relay board |
| DB-24PR |
24-channel power relay board |
| DB-24POR |
24-channel PhotoMos Relay output board |
| DB-24SSR |
24-channel Solid State Relay output board |
| DB-24C |
24-channel open-collector output board |
|
|
|
|
| |
|
|
|
|
|
| |
back |
|
| |
|
|
| |
|
|
| |
|
|
| |
|
|
|
|
|
| |
back |
|
| |
|
|
