|
|
|
|
∼Available soon∼ |
|
|
|
 |
| Model: PISO-PS600 |
|
|
PISO-PS600
PCI Bus, High-Speed, DSP-based, 6-axis Motion Control Card with FRnet |
 |
 |
|
|
| |
|
|
|
|
|
|
|
|
|
 |
|
|
| |
|
|
|
 |
|
|
|
|
|
The PISO-PS600 controller combines a new generation processor 1600 MIPS running up to 200 MHz, 9,526 logic element FPGA (Field Programmable Gate Array), I/O buffering circuitry, and motion control characterization software to control the position of 6-axis pulse command Servo/stepper motors. PISO-PS600 not only realizes the motion control with closed-loop (or semi closed-loop) and error handling, but also adopts the feed-forward gain to reduce speed profile following error to meet position control.
PISO-PS600 can be used on any IPC with 5 V PCI bus, and is suitable for general-purpose motion applications. This card also contains one FRnet port which allows IPC to expand its ability to have fast digital I/O control easily. This two-wired FRnet can have maximum 128 DI and 128 DO, and they are automatically scanned with a period of 0.72 ms. PISO-PS600 contains a DSP. Apart from a wide speed range, this intelligent motion controller also has a variety of built-in motion control functions, such as 2~6 axis linear interpolation, 2/3-axis circular interpolation, T/S-curve acceleration/deceleration, various synchronous actions, automatic homing, etc.
In addition, most of the PISO-PS600 motion control functions are performed with little load on the processor. The motion status, FRnet I/O, and the other I/O cards on IPC can still be
monitored while driving. As a result of the low CPU loading
requirements of the PISO-PS600, one or more motion cards can be used on
a single IPC. ICP DAS has also provided a variety of functions and
examples to reduce the need for programming by users, making it a
highly cost-effective solution for motion builders. |
|
|
|
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
- DSP-based motion control card with PCI
interface
- Independent 6-axis motion control
- Support both full-closed and semi-closed
control modes
- Maximum pulse output frequency: 4 Mpps.
- Maximum Encoder input frequency: 12 Mpps
- 4-step home mode with auto-searching
- 2 ~ 6-axis linear interpolation function
- 2/3-axis circular interpolation function
- Programmable T/S-curve acceleration and
deceleration
- Change speed and position on the fly
- High-speed position latch and compare
trigger
- Home sensor, positive and negative limit
sensors accepted for each axis
- Support fully-functional
manual-pulse-generator and jog functions
- Expandable distributed I/Os: 128 DI
& 128 DO via two-wired FRnet interface
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
 |
|
|
|
|
|
- Wafer Cutting
- Laser Cutting
- Toroid Winding Machine
- Tag Printer
- Fix-Pitch Stamping Machine
|
|
|
|
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
| PISO-PS600 |
PCI Bus, High-Speed, DSP-based, 6-axis Motion Control Card with FRnet |
|
|
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
| DN-8368GB |
The Daughter Board is for General Purpose |
| DN-8368MB |
The Daughter Board is for Mitsubishi J2S Amplifier |
| DN-20M |
The Daughter Board is for FRnet Connector and Full function Manual-Pulse-Generator |
| CA-MINI68-15 |
SCSI-II 68-pin Connector Cable 1.5 M |
| CA-SCSI20-M1 |
SCSI II 20-pin & 20-pin Male Connector Cable 1 M, for Mitsubishi Motor |
| CA-SCSI20-M3 |
SCSI II 20-pin & 20-pin Male Connector Cable 3 M, for Mitsubishi Motor |
| CA-SCSI20-M5 |
SCSI II 20-pin & 20-pin Male Connector Cable 5 M, for Mitsubishi Motor |
| CA-2P4C-0100 |
The Cable for FRnet Modules; Length: 100 M |
|
|
|
|
|
|
|
|
|
|
|
