|
| |
|
|
| |
| |
|
|
MSM-508FC-T 
8-Port Layer 2 Managed Switch with 2-Fiber Port and metal case |
 |
 |
 |
 |
 |
 |
 |
 |
|
|
|
|
| |
|
|
| |
|
|
| |
The MSM-508FC-T is an 8-Port Industrial Ethernet Layer 2 Managed Switch with 2-Port Fiber (SC Connector; Multi-mode) that secures data transmission by using fiber optics transmission to provide immunity from EMI/RFI interference. It is used Ethernet for transmitting a signal up to 2 Km(6,600 ft), and is the perfect solution for applications where transmission must be protected from electrical exposure, surges, lightning or chemical corrosion.
Fiber port of MSM-508FC-T operates at either half or full duplex mode. In full duplex mode, range is 2km with 62.5/ 125£gm fiber cables; in half duplex mode, range is 412m with 62.5/ 125£gm fiber cables. The Ethernet port of MSM-508FC-T supports 10/ 100M auto-negotiation feature and auto MDI /MDIX function.
It can be managed through RS-232 port via serial console or Ethernet port using telnet or Web browser. In addition, the switch supports a lot of powerful managed functions, such as 802.1Q Tag-based VLAN, Port-based VLAN, 802.1p QoS (Quality of Service), Port Trunking, Spanning Tree, Cable Testing and Port Mirroring. Built-in ICP DAS Cyber-Ring technique that enable multiple switches to be placed into a redundant ring. The switch detects and recovers from a fiber or copper link failure within approximately 50ms ¡V for the majority of applications a seamless process. Modbus/TCP, Modbus/RTU and OPC supported, SCADA application can monitor status of Ethernet and fiber port with Modbus or OPC protocol.
MSM-508FC-T provides two power inputs that can be connected simultaneously to live DC power sources. If one of the power inputs fails, the other live source acts as a backup to automatically support the MSM-508FC-T 's power needs. And, the relay output facility can deliver warning signal while dual power or network link failure.
|
|
| |
|
|
|
|
|
| |
|
|
| |
|
|
| |
|
|
| |
- Automatic MDI / MDI-X crossover for plug-and-play
- Each port supports both 10/100 Mbps speed auto negotiation
- Store-and-forward architecture
- Full duplex IEEE 802.3x and half duplex backpressure flow control
- 3.2Gbps high performance memory bandwidth
- Frame buffer memory : 1 Mbit
- Integrated look-up engine with dedicated 2 K unicast MAC addresses.
- Redundant Power Inputs +12 ~ +48 VDC
Power failure alarm by relay output
- Supports operating temperatures from -40¢XC ~ +75¢XC
- DIN rail mount and Screw hole for wall mounting kit.
|
|
| |
|
|
|
|
|
| |
|
|
| |
|
|
| |
|
|
| |
| Technology |
| Standards |
IEEE 802.3, IEEE 802.3u, IEEE802.3x |
| Processing Type |
Store & forward wire speed switching - no delays |
| MAC addresses supported |
2K |
| Memory Bandwidth |
3.2 Gbps |
| Flow Control |
IEEE802.3x flow control, back pressure flow control |
| Redundant strategy |
STP, Ring(ICP DAS) |
| Protocol |
VLAN, QoS, Port Trunk, SMTP, TELNET, SNMP |
| Interface |
| RJ45 port |
10/100BaseT(X) auto negotiation speed, F/H duplex mode,
and auto MDI/MDIX connection |
| Fiber Optics Port |
100 Base-FX(Multi-mode; SC connector) |
| LED Indicators |
10/100M, Link/Act/Backup, Full duplex/Half duplex(Fiber Port) |
| Ethernet Isolation |
1500 Vrms 1 minute |
| Frame Ground for EMS Protection |
Yes |
| Ethernet Transmission distance |
Ethernet : 2-pair UTP/STP Cat.3,4,5, EIA/TIA-568 100-ohm
Fast Ethernet : 2-pair UTP/STP Cat. 5, EIA/TIA-568 100-ohm |
| Fiber Optic Transmission distance |
Multi mode fiber cables:50/125, 62.5/125 or 100/140 £gm |
| Distance :2 km, (62.5/125 £gm recommended) for full duplex |
| Wavelength : 1300 or 1310nm |
| Min. TX Output:- 20 dBm |
| Max. TX Output: -14 dBm |
| Max. RX Sensitivity: -32 dBm |
| Max. RX Overload: -8 dBm |
| Budget: 12 dBm |
| Ethernet Cables |
10 Base-T (Cat.3, 4, 5 UTP cable; 100m Max.)
100 Base-TX (Cat.5 UTP cable; 100m Max.) |
| Management interface |
Console, DIP/Rotary Switch |
| Alarm output |
Relay |
| Digital Input/Output |
| Digital Input |
3-channel, Wet Contact, L: +11 VDC Max., H: +19 VDC ~ +30 VDC |
| Digital Output |
3-channel, Open Collector, Sink/NPN, 30V/100 mA Max. |
| Power |
| Input Voltage Range |
+12 ~ +48 VDC (Non-isolation redundant input) |
| Power Input isolation |
1 KV |
| Alarm Contact |
One relay output with current carrying capacity of 2A @ 30 VDC |
| Power Consumption |
0.3 A@24 VDC(+/- 5%, arrowed) |
| Protection |
Power reverse polarity protection |
| Frame Ground for EMS Protection |
Yes |
| Connection |
7-Pin Removable Terminal Block |
| Mechanical |
| Case |
Plastic |
| Flammability |
UL 94V-0 |
| Dimensions |
47 mm x 175 mm x 140 mm (W x H x D) |
| Installation |
DIN rail mount; Wall Mounting |
| Environmental |
| Operating temperature |
-40 ¢XC ~ +75 ¢XC |
| Storage Temperature |
-40 ¢XC ~ +85 ¢XC |
| Relative Humidity |
10% ~ 90% HR, non-condensing |
| Include cable |
| CA-090510 x 1 |
|
|
| |
|
|
|
|
|
| |
|
|
| |
|
|
| |
|
|
| |
| MSM-508FT-T CR |
8-Port Layer 2 Managed Switch with 2-Fiber Port, Multi Mode, ST Type (RoHS) |
| MSM-508FC-T CR |
8-Port Layer 2 Managed Switch with 2-Fiber Port, Multi Mode, SC Type (RoHS) |
| MSM-508FCS-T CR |
8-Port Layer 2 Managed Switch with 2-Fiber Port, Single Mode, SC Type (RoHS) |
| MSM-508FCS-40T CR |
8-Port Layer 2 Managed Switch with 2-Fiber Port, (40 km)Single Mode, SC Type (RoHS) |
|
|
| |
|
|
|
|
|
| |
|
|
| |
|
|
| |
|
|
| |
| CA-090510 |
9-Pin Female D-Sub & RJ-45 Cable, 1M Cable |
| MDR-20-24 |
24V/1A, 24 W Power Supply with DIN-Rail Mounting |
| KWM020-1824F |
24V/0.75A, 18 W Power Supply |
| DIN-KA52F |
24V/1.04A, 25 W Power Supply with DIN-Rail Mounting |
|
|
| |
|
|
|
|
|
| |
|
|
| |
|
|
|
|
