Copyright January 2002 by ICP DAS CO., LTD. All right reserved.

The ISaGRAF embedded driver is firmware burned into the flash memory of 
the I-8417 / 8817 / 8437 / 8837. It can be easily upgraded by the user.

Our newly released driver can also be obtained from the following website.
   ftp.icpdas.com/pub/cd/8000cd/napdos/isagraf/8000/driver/  

Warning:
  The copyright of the firmware and ISaGRAF embedded driver belongs to ICP DAS CO., LTD. 
  Only the I-8417, 8817, 8437 and 8837 have registered a legal ISaGRAF Target license. 
  To burn an ISaGRAF embedded driver into other I-8000 controllers is absolutely 
  illegal and may be punished by law.

Trademark:
  Products, names and trade names appeared belongs to their respective owner. 

This Document Details How To upgrade the OS & ISaGRAF driver For The I-8xx7 Embedded Controller.

Make sure of your current OS & driver version before you upgrade it. 

1. Create a file folder named "8000" in your hard drive. 
   For example, "c:\8000".

2. Copy \Napdos\ISaGRAF\8000\Driver\40M\motion5.00\"7188xw.exe", "7188xw.ini" , "7188xw.f4" ,
   "isa.exe" , "autoexec.bat" & "8k070515.img" from the CD_ROM into your "8000" folder.

3. Run "\8000\7188xw.exe" in your hard drive. A "7188xw" screen 
   will appear (Press F1 for help). 

4. Link COM1 or COM2 of your PC to COM1 of the I-8xx7 controller 
   through a RS232 cable. 
   If you PC is using another COM port (for example, COM5), 
   please exit 7188xw.exe first, then modify the first line in the 7188xw.ini file 
   as below  C1  B115200  P0  D8  S1    ===>   C5  B115200  P0  D8  S1 
   Then run 7188xw.exe again,

5. Power off the I-8xx7 controller, connect pin "INIT*" to "INIT* COM" 
   and then power it up.

6. If the connection is Ok, messages will appear on the 7188xw screen.

      ICP_DAS MiniOS7 for I-8000 Ver. 2.00 build 002,Apr 08 2005 17:06:02
      SRAM:512K, FLASH MEMORY:512K
      [CPU=RDC 8820-D]
      Serial number= 5A 5A 5A 5A 5A 5A 5A 5A
      i-8000>

7. Type "ver" to see the current OS version.

      i-8000> ver   

8. Type "isa *p=" to see the version No. of the ISaGRAF driver

      i-8000> isa *p=

      Driver  : : i-8xx7  : isa.exe - motion 4.29,Dec.26,2019
      MiniOS7 : Must use 8k070515.img
      isa_data.exe - 1.31,Dec.26,2019
      NED-ID  : 1
      COM1 is Modbus RTU slave port,19200,8,N,1 (or COM1 is free)
      COM2 is Modbus RTU slave port,19200,8,N,1 (or COM2 is Ethernet port)
      Use 'isa *f=1' to free COM1, 'isa *f=0' to set COM1 as Modbus RTU

      (C)Copyright:ICP DAS  CO. , LTD.      Taiwan Id:84517297

To upgrade an ISaGRAF embedded driver, follow the following steps.  

9. Power off the I-8xx7 controller, connect pin "INIT*" to "INIT* COM" 
   and then power it up.

10. Press "F4" to auto run "isa_data.exe" and dowload "autoexec.bat","isa.exe"
    ,"8k070515.img" and reboot system. Wait about 90 SEC. to update ISaGRFA system.
   
   ***DO NOT REMOVE THE POWER IN THESE 90 SEC.***   

11. Type "dir" to make sure "autoexec.bat" and "isa7188e.exe" 
    are well burned.

      i-8000> dir
       0)autoexec.bat 05/21/2005 06:40:00     22[00016]8002:0000-8003:0006
       1)isa.exe      08/26/2015 17:51:09 179751[2BE27]8005:000-ABE7:000D
      Total File number is 2  Free space=27883 bytes

12. Press ALT_X to exit "7188xw".

13. Remove the connection between "INIT*" - "INIT* COM", reset the I-8xx7.
