|
|
|
|
|
|
|
NS-200WDM Series
Industrial Single-Strand 10/100 Base-T(X) to 100 Base-FX Media Converters |
 |
 |
 |
 |
 |
 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Using the fiber optic medium for Ethernet applications has become more popular due to fiber optic's excellent physical features, especially for long distance networks. However, fiber optic cable is very expensive, so if we can apply a solution that uses only 1 cable instead of 2, the infrastructure cost can be cut in half.
The NS-200WDM Series provides a solution that reduces your expense by 50%!
The NS-200WDM Series of Single-Strand Fiber Converters supports Wavelength Division Multiplexing (WDM) technology that allows two independent data communication channels to transmit and receive over one standard, single mode, fiber optic line. This not only doubles your existing bandwidth, but also effectively reduces the cost of creating a new fiber optic infrastructure.
50% Cost Saving for Fiber Optic Infrastructures
With a pair of NS-200WDM series products (NS-200WDM-A and NS-200WDM-B), you can double the utilization of your existing, costly fiber optic cable, and save 50% of the cost of a newly installed fiber optic application.
It contains "soft start" function with overload protection, high-low voltage protection.
The width of the NS-200WDM is just 32mm, so it can be used where space is important.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
- Automatic MDI / MDI-X crossover for plug-and-play
- Supports both 10/100 Mbps speed auto negotiation
- Store-and-forward architecture
- Full duplex IEEE 802.3x flow control
- 1.4Gbps high performance memory bandwidth.
- Power Input, +12 ~ +48 VDC
- Reverse Polarity Protection
- Supports operating temperatures from 0 ~ +70¢XC
- DIN-Rail
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Technology |
Standards |
IEEE802.3, 802.3u, 802.3x |
Processing Type |
Store & forward wire speed switching |
MAC Addresses |
1024 |
Memory Bandwidth |
1.4 Gbps |
Flow Control |
IEEE802.3x flow control flow control |
Interface |
RJ45 port |
10/100BaseT(X) auto negotiation speed, and auto MDI/MDIX connection |
Fiber Optic port |
100 Base-FX(Single-mode;
SC connector) |
LED Indicators |
10/100M, Link/Act, Full duplex(Fiber Port) |
Ethernet Isolation |
1500 Vrms 1 minute |
Frame Ground for EMS Protection |
Yes |
Fiber Optic |
Single-mode fiber cables:8.3/125, 8.7/125, 9/125 or
10/125 £gm |
Distance :15
km, (9/125 £gm mrecommended)
for full duplex |
Wavelength :
TX: 1310, RX: 1550 nm for NS-200WDM-A
TX: 1550, RX: 1310 nm for NS-200WDM-B |
Min. TX
Output:- 14 dBm |
Max. TX Output: -8 dBm |
RX
Sensitivity: -31 dBm |
Ethernet Transmission distance |
Ethernet : 2-pair UTP/STP Cat.3,4,5, EIA/TIA-568 100-ohm |
Fast Ethernet : 2-pair UTP/STP Cat. 5, EIA/TIA-568 100-ohm |
Power |
Input Voltage Range |
+12 ~ +48 VDC (Non-isolation) |
Power consumption |
0.12 A @ 24 VDC, +/- 5% arrowed with 100M Full duplex |
LED Indicator |
Yes |
Protection |
Power reverse polarity protection |
Frame Ground for EMS Protection |
Yes |
Connection |
3-Pin Removable Terminal Block |
Case |
Plastic |
Flammability |
UL 94V-0 |
Dimensions |
32.30mm x 99.00mm x 77.50mm (W x H x D) |
Installation |
DIN rail mount |
Environmental |
Operating Temperature |
0 ~ +70¢XC |
Storage Temperature |
-20 ~ +85¢XC |
Ambient Relative
Humidity |
10% ~ 90% non-condensing |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
NS-200WDM-A CR |
10/100BaseT(X) to 100BaseFX Single-Strand Media Converter, TX 1310 nm, RX 1550 nm, SC (RoHS) |
NS-200WDM-B CR |
10/100BaseT(X) to 100BaseFX Single-Strand Media Converter, TX 1550 nm, RX 1310 nm, SC (RoHS) |
Important Note : You must purchase both NS-200WDM-A and NS-200WDM-B since these products work as a pair. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PWR-24/110 |
24 V/0.2 A Power Supply, (No-mounting) |
KWM020-1824F |
24 V/0.75 A Power Supply, (No-mounting) |
DIN-KA52F |
24 V/1 A Power Supply, (With DIN-Rail mounting) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|