CAN-8124-G

DeviceNet Remote I/O Unit with 1 I/O Slot
CAN-8124-G
CAN-8124-G
CAN-8124-G
CAN-8124-G
CAN-8124-G
CAN-8124-G
CAN-8124-G
CAN-8124-G
CAN-8124-G
CAN-8124-G
CAN-8124-G
CAN-8124-G

Features

  • DeviceNet Version : DeviceNet Specification Volume I & II, Release 2.0
  • Number of Nodes : 64(Max)
  • Support Message Groups : Group 2 only Server
  • UCMM : Not Support
  • I/O Operating Modes : Poll, Bit-Strobe, Change of State/ Cyclic
  • No. of Fragment I/O : 128 Bytes (Max) (Input/ Output)
  • MAC ID Setting : Rotary Switch
  • Baud Rate Setting : Rotary Switch
CE FCC WEEE

Introduction

The CAN-8124 main control unit is specially designed for the slave device of DeviceNet protocol. It follows the Specification of DeviceNet. In order to expand I/O channel more flexible, an CAN-8124 supports 1 slot for I/O expansion and suits with a lot of ICP DAS DI/AI/DO/AO modules. Users can choice DI/DO/AI/AO modules of I-87K series or I-8000 series to fit the customized practice applications. In addition, we also provide CAN Slave Utility to allow users to create the EDS file dynamically. The EDS file is based on DeviceNet and can be compatible with different DeviceNet master interfaces.

Applications


  • Automotive
  • Food & Beverage
  • Packaging
  • High-speed Assembly
  • Pulp & Paper
  • Semiconductor Fabrication
  • Control System...etc.

Ordering Information

PRODUCT SERIES DESCRIPTION QNT. INQUIRY
PRODUCT SERIES CAN-8124-G DESCRIPTIONDeviceNet Remote I/O Unit with 1 I/O Slot
This combination include other products.

Similar Products

CPU Module
CPU 80186, 80 MHz or compatible
EEPROM 16 KB
Flash 512 KB
NVRAM 31 bytes (battery backup, data valid for up to 10 years)
SRAM 512 KB
Real Time Clock Yes
Watchdog Timer Watchdog IC
LED Indicators
Status 1 x Power
2 x DeviceNet status
I/O Expansion
Slots 1 slots
DeviceNet
Controller NXP SJA1000T with 16 MHz clock
Ports 1
Connection Supported 1 connection for Explicit Messaging
1 connection for Polled I/O
1 connection for Bit-Strobe I/O
1 connection for COS/Cyclic I/O
Baud Rate 125 k, 250 k, 500 k
Isolation 3000 VDC for DC-to-DC, 2500 Vrms for photo-couple
Terminal Resistor Jumper for 120 Ω terminal resistor
Specification Volume I, Release 2.0 & Volume II, Release 2.0
Node ID 0 ~ 63
Shutdown Message Yes
Subscribe Group 2 Only Server
Power
Input Range +10 VDC ~ +30 VDC
Consumption 1.7 W
Mechanical
Dimensions (mm) 64 x 119 x 91 (W x L x H)
Installation DIN-Rail
Environment
Operating Temperature -25 ~ +75 ℃
Storage Temperature -30 ~ +80 ℃
Humidity 10 ~ 90% RH, Non-condensing

In the CAN-8124/CAN-8224 device, ICPDAS provides CAN Slave Utility to produce the specific EDS file with the plugged in modules in off-line mode. After finishing the utility configuration, it can create the EDS file. There is also much DeviceNet information of the CAN-8x24 in the EDS file. It is not only for DeviceNet master interface but also for users to know more information about the slave device. Users also can use the default configuration for general DI/DO/AI/AO. And users only need to set the MAC ID and Baud rate by hardware rotary switch. Then, after wire connection and the CAN-8x24 powered on, it can work normally on the CAN bus network through DeviceNet protocol. 


Design Flowchart 

The following simple steps show how to use CAN-8x24 in DeviceNet protocol.