|
| |
|
| |
| |
|
|
RSM-405FT 
5-Port Real-time Redundant Ring Switch with 2-Fiber Port, Multi Mode, ST Type, metal case |
 |
 |
 |
 |
 |
 |
|
|
|
|
|
|
 |
|
|
| |
|
|
| |
The RSM-405FT is a 5-Port Industrial Ethernet Real-Time Redundant Ring Switch with 2-Port Fiber (ST Connector; Multi-mode) that secures data transmission by using fiber optics transmission to provide immunity from EMI/RFI interference. It is used Ethernet for transmitting a signal up to 2 km(6,600 ft), and is the perfect solution for applications where transmission must be protected from electrical exposure, surges, lightning or chemical corrosion.
Fiber port of RSM-405FT operates at either half or full duplex mode. In full duplex mode, range is 2km with 62.5/ 125£gm fiber cables; in half duplex mode, range is 412m with 62.5/ 125£gm fiber cables. The Ethernet port of RSM-405FT supports 10/ 100M auto-negotiation feature and auto MDI /MDIX function.
Built-in ICP DAS Cyber-Ring technique that enable multiple switches to be placed into a redundant ring. It detects and recovers from a fiber or copper link failure within approximately 300ms ¡V for the majority of applications a seamless process. Modbus/TCP, Modbus/RTU and OPC supported, SCADA application can monitor status of Ethernet and fiber port with Modbus or OPC protocol.
RSM-405FT provides two power inputs that can be connected simultaneously to live DC power sources. If one of the power inputs fails, the other live source acts as a backup to automatically support the RSM-405FT's power needs. And, the relay output facility can deliver warning signal while dual power or network link failure.
|
|
| |
|
|
|
|
|
| |
|
|
| |
|
|
| |
|
|
| |
- Automatic MDI / MDI-X crossover for plug-and-play
- Each port supports both 10/100 Mbps speed auto negotiation
- Store-and-forward architecture
- Full duplex IEEE 802.3x and half duplex backpressure flow control
- 3.2Gbps high performance memory bandwidth
- Frame buffer memory : 512 Kbit
- Integrated look-up engine with dedicated 1 K unicast MAC addresses.
- Redundant Power Inputs +10 ~ +30V DC
Power failure alarm by relay output
- Supports operating temperatures from 0¢XC ~ +70¢XC
- DIN rail mount and Screw hole for wall mounting kit.
|
|
| |
|
|
|
|
|
| |
|
|
| |
|
|
| |
| Technology |
| Standards |
IEEE 802.3, IEEE 802.3u, IEEE802.3x |
| Processing Type |
Store & forward wire speed switching - no delays |
| MAC addresses supported |
1024 |
| Memory Bandwidth |
3.2 Gbps |
| Flow Control |
IEEE802.3x flow control, back pressure flow control |
| Redundant strategy |
STP, Ring(ICP DAS) |
| Protocol |
Modbus/RTU, Modbus/TCP, OPC, STP, Cyber Ring |
| Interface |
| RJ45 port |
10/100BaseT(X) auto negotiation speed, F/H duplex mode,
and auto MDI/MDIX connection |
| Fiber Optics Port |
100 Base-FX(Multi-mode; ST connector) |
| LED Indicators |
10/100M, Link/Act/Backup, Full duplex/Half duplex(Fiber Port) |
| Ethernet Isolation |
1500 Vrms 1 minute |
| Frame Ground for EMS Protection |
Yes |
| Ethernet Transmission distance |
Ethernet : 2-pair UTP/STP Cat.3,4,5, EIA/TIA-568 100-ohm
Fast Ethernet : 2-pair UTP/STP Cat. 5, EIA/TIA-568 100-ohm |
Fiber Optic
Transmission distance |
Multi mode fiber cables:50/125, 62.5/125 or 100/140 £gm |
| Distance :2 km, (62.5/125 £gm recommended) for full duplex |
| Wavelength : 1300 or 1310nm |
| Min. TX Output: -20 dBm |
| Max. TX Output: -14 dBm |
| RX Sensitivity: -34 to -31 dBm |
| Ethernet Cables |
10 Base-T (Cat.3, 4, 5 UTP cable; 100m Max.)
100 Base-TX (Cat.5 UTP cable; 100m Max.) |
| Management interface |
Console, DIP/Rotary Switch |
| Alarm output |
Relay |
| Power |
| Input Voltage Range |
+10 ~ +30VDC(Removable Terminal Block) |
| Power Input isolation |
1KV |
| Alarm Contact |
One relay output with current carrying capacity of 2A @ 30 VDC |
| Power consumption |
0.3A@24Vdc (+/- 5%, arrowed) |
| Protection |
Power reverse polarity protection |
| Frame Ground for EMS Protection |
Yes |
| Connection |
7-Pin Removable Terminal Block |
| Mechanical |
| Case |
Metal |
| Environmental rating |
IP20 |
| Dimensions |
72.5mm x 110mm x 102mm (W x H x D) |
| Installation |
DIN rail mount; Wall Mounting |
| Environmental |
| Operating temperature |
0 ¢XC~ +70¢XC |
| Storage Temperature |
-20 ~ +85¢XC |
| Relative Humidity |
10% to 90% non-condensing |
| Include cable |
| CA-090510 x 1 |
|
|
| |
|
|
|
|
|
| |
|
|
| |
|
|
| |
| RS-405FC CR |
5-Port Real-time Redundant Ring Switch with 2-Fiber
Port, Multi Mode, SC Type (RoHS) |
| RS-405FCS CR |
5-Port Real-time Redundant Ring Switch with 2-Fiber
Port, Single Mode, SC Type (RoHS) |
| RS-405FT CR |
5-Port Real-time Redundant Ring Switch with 2-Fiber
Port, Multi Mode, ST Type (RoHS) |
| RSM-405FC CR |
5-Port Real-time Redundant Ring Switch with 2-Fiber
Port, Multi Mode, SC Type, metal case (RoHS) |
| RSM-405FCS CR |
5-Port Real-time Redundant Ring Switch with 2-Fiber
Port, Single Mode, SC Type, metal case (RoHS) |
| RSM-405FT CR |
5-Port Real-time Redundant Ring Switch with 2-Fiber Port, Multi Mode, ST Type, metal case (RoHS) |
|
|
| |
|
|
|
|
|
| |
|
|
| |
|
|
| |
| CA-090510 |
9-pin Female D-sub & RJ-45 cable, 1M Cable |
| PWR-24/110 |
24V/0.2A Power Supply, (No-mounting) |
| KWM020-1824F |
24V/0.75A Power Supply, (No-mounting) |
| DIN-KA52F |
24V/1A Power Supply, (With DIN-Rail mounting) |
|
|
| |
|
|
|
|
|
| |
|
|
| |
|
|
|
|
