LC-223H

1-channel Dimmer Control Module
LC-223H
LC-223H
LC-223H
LC-223H
LC-223H
LC-223H
LC-223H
LC-223H
LC-223H
LC-223H
LC-223H
LC-223H

Features

  • Isolated Analog Output (0 to 20 mA, 0 to 10 V, 1 to 10 V) For Dimming Control
  • Relay Operation Current: 16 A (Res. Load)
  • Support Lighting Module (Max.):
  • Incandescent Lamp: 40W/ 220VAC * 8 Sets
  • LED(Electronic ballast): 40W/ 220VAC * 10 Sets
  • Provide Power Relay Output to turn ON/OFF the Dimming Ballast
  • Isolated Analog Output(0 to 20 mA, 0 to 10 V, 1 to 10 V) for Dimming Control
  • Provide the wall Switch function to Control the Brightness of the Dimming Ballast
  • Provide The Dry Contact to trigger the Brightness of the Dimming Ballast
  • Supports Modbus RTU and DCON Protocols
CE UKCA FCC RoHS WEEE

Introduction

The LC-223H is an easy-to-use dimming ballast control module that can be easily installed and operated without requiring specialist knowledge or skills. The brightness of a fluorescent lamp can be controlled using a dimmer, either via digital input or a host controller. The digital input can be used to directly control the light value of the luminous flux in sequence from 10% to 100%, without the need for a remote host controller. 4 kV ESD,2kV SURGE protection and 2500 VDC intra-module isolation are also provided. When required, communication with the LC-223H is programmable based on the Modbus RTU/DCON protocol, with the added benefit that diff erent addresses can be set via hardware configuration.

Applications

Ordering Information

PRODUCT SERIES DESCRIPTION QNT. INQUIRY
PRODUCT SERIES LC-223H     CR DESCRIPTION1-channel Dimmer Control Module with 2-channel Dry Contact Input Trigger (RoHS)
This combination include other products.

Similar Products

Isolation
Intra-module Isolation 2500 VDC
EMS Protection
EFT (IEC 61000-4-4) ±4 kV for Power
ESD (IEC 61000-4-2) ±4 kV contact for each Terminal
±4 kV Air for Random Point
Surge (IEC 61000-4-5) ±2 kV for Power
LED Indicators
Status 1 LED as Power Indicator
Analog Output
Channels 1
Type 0 ~ 20 mA, 4 ~ 20 mA, 0 ~ 10 V, 1 ~ 10 V
Resolution 12-bit
Accuracy ±0.1% of FSR
DA Output Response Time 10 ms
Voltage Output Capability 20 mA
Current Load Resistance 450 Ω
Digital Input
Channels Dry Contact: 2 for the Dimming Trigger
Wet Contact: 1 for the Wall Switch Control
Type Dry + Wet Contact
ON Voltage Level Wet: 65 VAC ~ 240 VAC
Dry: Close to GND
OFF Voltage Level Wet: 58 VAC Max.
Dry: Open
Relay Output
Channels 1
Type Power Relay, Form A (SPST N.O.)
Contact Rating 16 A (Res. load)
(1).250 VAC (Recommend Working Current 1.5 A)
Operate Time 10 ms Max.
Release Time 5 ms Max.
Electrical Endurance 120,000 ops.
Mechanical Endurance 5,000,000 ops.
Power on Value Yes, programmable
Safe Value Yes, programmable
Application Specification (1).Incandescent Lamp: 40W/220VAC * 8 Sets
(2).LED (Electronic ballast): 40W/220VAC * 10 Sets
COM Ports
Ports 1 x RS-485
Baud Rate 1200 ~ 115200 bps
Data Format (N, 8, 1)
Protocol DCON, Modbus RTU
Power
Reverse Polarity Protection Yes
Consumption 1.5 W Max.
Powered from Terminal Block Yes, 10 ~ 30 VDC
Mechanical
Dimensions (mm) 72 x 100 x 59 (W x L x H)
Installation DIN-Rail
Environment
Operating Temperature -25 ~ +75°C
Storage Temperature -30 ~ +80°C
Humidity 10 ~ 95% RH, Non-condensing